Kuiz Chapter 2.5

1.       When configuring an ISR device using Cisco SDM Express Wizard, what setting Enable Secret Password field accomplish?

·        Ensure that authorization be granted before accessing the internet

·        Blocks unauthorized from accessing LAN

·        Controls acces to user excecutable mode

·        Controls access to privileged mode

2.       When using Cisco SDM, which WAN encapsulation type can be configured to require a username and password before a connection is granted?

·         High-level data link control (HLC)

·         Frame relay

·         Point-to-point protocol (PPP)

·         ATM PVC

3.       What speed and duplex setting will result on a Catalyst switch if is sert to auto-negotitate speed and duplex and is connected to a 100 Mbps port on a device that does not support aoto-negotiation?

·        10 half duplex

·        10 full duplex

·        100 half duplex

·        100 full duplex

4.       Which method can be used to configure a Cisco Catalyst switch before an IP addres has been applied to the management interface?

·         Cisco IOS CLI using Vlan 1

·         Cisco IOS CLI using console port

·         Cisco device manager using console port

·         Cisco View software using Vlan

5.       What is a secure way that a client can connect to a device in-band for the purpose of remote monitoring and aministration?

·        Telnet

·        HTTP

·        SSH

·        Console port

6.       Which type wide area network (WAN) connection uses packets switched networks?

·         ISDN

·         Dial-up

·         Frame relay

·         Point-to-point

7.       A small company with two offices in the same builing is requesting advice on WAN connections. Which two questions would give a technician information to base a recommendation? (Choose two.)

·         What operating system is being used?

·         How much money has the customer budgeted to spend on the WAN connections?

·         What type of e-mail client software is used by the employees

·         Are the computers laptop or workstations

·         Are the company web servers located in the building or at the ISP?

8.       What is one fundamental difference between Cisco’s CLI versus the SDM interface?

·         The SDM interface can be used with both in band and out-of-band management.

·         The CLI interface can be used with both in-band and out-of-band management.

·         The SDM interface require a terminals emulation program on the PC

·         The CLI interface cannot be used over a Telnet connection

9.       Which two statements describe the commad history feature? (Choose two.)

·        It requires configuration of a history buffer before it can be used.

·        It displays the most recently entered command strings in the current mode

·        It saves the output from the most recent show command.

·        It display the last five commands that were entered in global configuration mode

·        It can accessed by using the up and down arrow keys.

10.   Which router mode displays a prompt of Router#?

·         Global configuration mode

·         Privileged EXEC mode

·         Setup mode

·         User EXEC mode

11.   In which two cases would out-of-band management of a router be required? (Choose two.)

·         When accessing a customer router from the ISP to monitor the normal operation

·         To acces and configure the router before the IP network is operational

·         To correct an error that has shutdown the network interface on a router

·         When the NAT translation configuration settings are incorrect

·         To back up the running configuration on tftp server

12.   Which two statement statements describe the result of entering the ip route 0.0.0.0 0.0.0.0 192.168.1.1 command on a rounter? (Choose two.)

·         The router is not able to reach the 192.168.1.0 network.

·         All packets received by the router are sent to address 192.168.1.1

·         The remote network 192.168.1.0 can be reached using any interface

·         A default static route is added to the routing table.

·         If a route to a destination network is not known, the packets is sent 192.168.1.1

13.   Click and drag the command on the left to the correct on the right.

Used to change router modes or sub-modes

Interface fastethernet 0/0

Configure terminal

enable

   

     Used by administrators to verify or monitor router operation

Show interfaces

ping

Show ip route

Affects the operation of the network

ip address 172.16.1.1 255.255.255.0

no shutdown

14.   What is the purpose of assigning an IP address to the interface VLAN1 on the Cisco switch?

·         To be able to telnet to the switch to manage and configure it

·         To enable the switch to route between networks

·         To create a new IP local network on the switch

·         To permit IP packets to be forward by the switch