Rabu, 05 Januari 2011

Lab 4.5.3 Building Straight-Through and Crossover UTP Cables

Part A: Build and test an Ethernet straight-through patch cable
Step 1: Obtain and prepare the cable
a. Determine the length of cable required. This could be from a device such as a computer to the device to which it connects (like a hub or switch) or between a device and an RJ-45 outlet jack. Add at least 30.48 cm (12 in.) to the distance. The TIA/EIA standard states the maximum length is 5 m (16.4 ft.). Standard Ethernet cable lengths are usually .6 m (2 ft.), 1.83 m (6 ft.), or 3.05 m (10 ft.).
b. Which length of cable did you choose and why did you choose this length?
Jawaban : 6m (2 ft) 
c. Cut a piece of cable to the desired length. Stranded UTP cable is commonly used for patch cables (the cables between an end network device such as a PC and an RJ-45 connector) because it is more durable when bent repeatedly. It is called stranded because each of the wires within the cable is made up of many strands of fine copper wire, rather than a single solid wire. Solid wire is used for cable runs that are between the RJ-45 jack and a punch-down block.
d.  Using wire strippers, remove 5.08 cm (2 in.) of the cable jacket from both ends of the cable.


Step 2: Prepare and insert the wires 
a. Determine which wiring standard will be used. Circle the standard. [T568A | T568B] 
b. Locate the correct table based on the wiring standard used. 
c. Spread the cable pairs and arrange them roughly in the desired order based on the standard chosen. 
d. Untwist a short length of the pairs and arrange them in the exact order needed by the standard. It is very important to untwist as little as possible. The twists are important because they provide noise cancellation. 
e. Straighten and flatten the wires between your thumb and forefinger. 
f. Ensure the cable wires are still in the correct order as the standard. 
g. Cut the cable in a straight line to within 1.25 to 1.9 cm (1/2 to 3/4 in.) from the edge of the cable jacket. If it is longer than this, the cable will be susceptible to crosstalk (the interference of bits from one wire with an adjacent wire). 
h. The tang (the prong that sticks out from the RJ-45 connector) should be on the underside pointing downward when inserting the wires. Insert the wires firmly into the RJ-45 connector until all wires are pushed as far as possible into the connector.


Step 3: Inspect, crimp, and re-inspect 
a. Visually inspect the cable and ensure the right color codes are connected to the correct pin numbers. 
b. Visually inspect the end of the connector. The eight wires should be pressed firmly against the end of the RJ-45 connector. Some of the cable jacket should be inside the first portion of the connector. This provides strain relief for the cable. If the cable jacket is not far enough inside the connector, it may eventually cause the cable to fail. 
c. If everything is correctly aligned and inserted properly, place the RJ-45 connector and cable into the crimper. The crimper will push two plungers down on the RJ-45 connector. 
d. Visually re-inspect the connector. If improperly installed, cut the end off and repeat the process.


Step 4: Terminate the other cable end 
a. Use the previously described steps to attach an RJ-45 connector to the other end of the cable. 
b. Visually re-inspect the connector. If improperly installed, cut the end off and repeat the process. 
c. Which standard [T568A | T568B] is used for patch cables in your school? 
Jawaban: [T568A]


Step 5: Test the cable 
a. Using a cable tester, test the straight-through cable for functionality. If it fails, repeat the lab. 
b. (Optional) Use the cable to connect a PC to a network. 
c. (Optional) Click the Start button and select the Run option. 
d. (Optional) Type cmd and press Enter
e. (Optional) From the command prompt, type ipconfig
f. (Optional) Write down the default gateway IP address.
Jawaban : 255.0.0.0
g. (Optional) From the command prompt, type ping followed by the default gateway IP address. If the cable is functional, the ping should be successful (provided that no other network problem exists and the default gateway router is connected and functional).


Part B: Build and test an Ethernet crossover cable
Step 1: Obtain and prepare the cable 
a. Determine the length of cable required. This could be from a hub to a hub, hub to switch, switch to switch, computer to router, or from one computer to another computer. Add at least 30.48 cm (12 in.) to the distance. Which length of cable did you choose and why did you choose this length? 
b. Cut a piece of cable to the desired length and, using wire strippers, remove 5.08 cm (2 in.) of the cable jacket from both ends of the cable.


Step 2: Prepare and insert the T568A wires 
a. Locate the T568A table at the beginning of the lab. 
b. Spread the cable pairs and arrange them roughly in the desired order based on the T568A standard. 
c. Untwist a short length of the pairs and arrange them in the exact order needed by the standard. It is very important to untwist as little as possible. Twists are important because they provide noise cancellation. 
d. Straighten and flatten the wires between your thumb and forefinger. 
e. Ensure the cable wires are in the correct order based on the standard. 
f. Cut the cable in a straight line to within 1.25 to 1.9 cm (1/2 to 3/4 in.) from the edge of the cable jacket. If it is longer than this, the cable will be susceptible to crosstalk (the interference of bits from one wire with an adjacent wire). 
g. The tang (the prong that sticks out from the RJ-45 connector) should be on the underside pointing downward when inserting the wires. Insert the wires firmly into the RJ-45 connector until all wires are pushed as far as possible into the connector.


Step 3: Inspect, crimp, and re-inspect 
a. Visually inspect the cable and ensure the right color codes are connected to the correct pin numbers. 
b. Visually inspect the end of the connector. The eight wires should be pressed firmly against the RJ-45 connector. Some of the cable jacket should be inside the first portion of the connector. This provides for cable strain relief which can eventually cause the cable to fail. 
c. If everything is correctly aligned and inserted properly, place the RJ-45 connector and cable into the crimper. The crimper will push two plungers down on the RJ-45 connector. 
d. Visually re-inspect the connector. If improperly installed, cut the end off and repeat the process.


Step 4: Terminate the T568B cable end 
a. On the other end, use the previously described steps (but use the T568B table and standard) to attach an RJ-45 connector to the cable. 
b. Visually re-inspect the connector. If improperly installed, cut the end off and repeat the process. 
c. Which standard [T568A | T568B] would you rather use at home if you have or would like to have a home network?


Step 5: Test the cable
a. Using a cable tester, test the crossover cable for functionality. If it fails, repeat the lab.
b. Use the cable to connect two PCs.
c. On both computers, click the Start button and select Run.
NOTE: If the Run command is unavailable on your PC, visually check the LED status lights on the NIC card. If they are on (usually green or amber) the cable is functional.
d. On both computers, type cmd and press Enter.
e. On both computers from the command prompt, type ipconfig.
f. Write the IP address of both computers.
Computer 1:
Computer 2:
g.    From the command prompt of one computer, type ping followed by the IP address of the other computer. If the cable is functional, the ping should be successful. Do the ping on the other computer as well.
NOTE: The Windows Firewall on the target computer must be temporarily disabled for the ping to be successful. Refer to Lab 3.1.5 if you need help with this. If you disable the firewall, be sure to re-enable it.


Step 6: Reflection 
a. Which part of making these cables did you find the most difficult? Compare your views with a classmate. 
b. Are all four pairs of cables twisted the same amount? Discuss the reasons why or why not.
Jawaban : Tidak. Setiap kabel memiliki perbedaan tersendiri. 
c. Ask a local business or check a site such as http://www.workopolis.com/ to see how much a beginning cable installer earns and which criteria they look for in a cable installer. Write the information you discover in the space provided. 
d. Many technicians keep a crossover cable in their toolkit. When do you think that you would use a crossover cable and when do you think a network technician would use this cable?
Jawaban : kabel cross digunakan untuk menghubungkan 2 perangkat yang berbeda.

Tidak ada komentar:

Posting Komentar